Linksys Router Red Light Issue: How To Fix It?

 The condition of your Linksys WiFi router's LED lights affects how well it performs. You might not frequently notice a red light on your Linksys router. What happens, though, if your Linksys red light persists? However, the red light issue with Linksys routers occurs constantly. If the problem isn't resolved, you won't be able to utilize the internet with your devices. In the following section,  offer you some tried-and-true recommendations to help you fix the Linksys glowing red issue.

Verify The Power Supply

To begin with, confirm that the outlets where your router or repeater connect are functional and producing enough power. If not, you might want to experiment with different socket placements to fix the red light issue.

Check The Wire Connectivity

Another potential source of the Linksys red light issue is faulty or loose wire connections. Consequently, make sure the Ethernet cable plugs in properly and it does not cut or otherwise damage. Before using it connect the router or extender to your computer.

Check For Compatibility

When linking a router to an extender, it is essential to ensure that a modem and router can interact with one another. Therefore, check that the device you select to satisfy your internet needs is appropriate.

Firmware Upgrading

• You must first sign in to your Linksys cloud account.
• After the web interface has loaded, select the connection.

Note: Open your internet browser and input an Internet Protocol (IP) address in the URL box if you don't have a Linksys account to enter the router configuration.

• Look for the box to enable the option for automatic firmware updates below the area for firmware upgrades. When it finishes, press the OK button to secure each of the modifications.
• Tap Accept in the box that appears and asks if you want to upgrade your software.
• Your screen will display a message asking you to reset your router; select OK to proceed.
• Finally, a firmware update for the Linksys router finished successfully.

Note: You may also update the firmware on your Linksys extender if the problem persists. If you are unsure of how to upgrade an extender's firmware, visit extender.linksys.com and perfectly complete all the instructions that appear.

Reset The Linksys WiFi Router

Try resetting the Linksys router to its original configuration if the aforementioned solutions to the red light on Linksys router issue didn't work. Now, check the Linksys router for a reset button. The reset button is located on the bottom or back. Continue to press and hold the reset button on the Linksys router for approximately 10 seconds later using a paperclip or other tiny object. The Linksys router LEDs will then all turn off. Finally, repeat the Linksys router installation procedure. 

Get In Touch With Linksys Support

After attempting the aforementioned measures to resolve the red light issue, it’s advised to contact Linksys customer service for additional assistance. If there is a hardware issue with the router, they can provide you with a precise solution step and the fix as well.

Tip: Try buying a Linksys extender gadget and going through the login and installation procedures if you want to increase the WiFi signal range of your Linksys router. 

Login To The Linksys WiFi Extender

Connect the Linksys extender plug-in outlet first. But, if the power LED of the Linksys extender blinking orange then plug it in again. Next, connect your WiFi device, such as a laptop or PC, to the Linksys extender network. Now, type extender.linksy.com into the browser to visit the Linksys online administration page. Finish by entering all of the credentials that show on the display page. To finish the Linksys extender login process, select the login option. 

Setup Instructions For Linksys Extender 

There are two methods to carry out the Linksys extender setup procedure:

Setup Of Linksys Extender Through WPS

Set up the Linksys extender gadget initially close to the router. Push the WPS buttons on the Linksys repeater and the current router after that. Next, observe the extender and router device's solid WPS LED for a brief period of time. As a result, it indicates that the repeater and router successfully connect. 

Although some routers do not support the WPS button, the majority of users are unable to complete the extender setup procedure. So, try a different approach to configuring your Linksys extender. 

Setup Through Web UI

Navigate to the Linksys web management page to complete this approach. Then, look for the option for the setup wizard and choose the WiFi network that you wish to expand or enlarge. You can then look at the text that says "Extender successfully configured" on the laptop's display by entering the security password and tapping the link button. 

After taking into account the procedures of the aforementioned two approaches, the Linksys extender setup procedure thus finishes. 

Once you've read everything on this page, you'll be able to fix the Linksys router red light problem. In any instance, try contacting or pinging our Linksys team specialists by submitting inquiries to the official email at care@linksyswifiextender.net if you are unable to resolve the red light issue with the Linksys router.